单词crank的英汉翻译


crank

[kræŋk]
    adj.脾气暴燥的,易怒的 n.[机]曲柄,奇想 vt.[机]装曲柄 vi.[机]转动曲柄







单词crank的英汉对照例句


旋开曲轴上的机油分离器。
Undo oil separator on the crankshaft.
应用正交试验方法,系统分析了曲轴树脂砂铸造低压浇注铁水充型过程,确定的低压浇注工艺规范,经过曲轴铸造生产验证,获得了优质曲轴铸件。
Applying orthogonality test method to analyze the crankshaft resin sand casting pouring molten iron of low pressure cast.the high quality crankshaft has been gotten by definite pouring technology specification of low pressure cast its pouring technology scheme design of low pressure is reasonable.
用油石去除曲轴箱孔上的所有锐边或毛边!
Remove any sharp edges or burrs on the crankshaft case bore using an oilstone!
用油石仔细剔除曲轴法兰倒棱上的小边或毛刺。
Carefully remove small edges or burrs on the chamfer of the crankshaft flange with an oilstone.
用于安装小型ptfe曲轴密封圈,第2代997
For fitting the small ptfe crankshaft sealing ring 2nd generation997
油盘和气缸体的下部共同称为曲轴箱,用来封闭或罩住曲轴。
"The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose or encase the crankshaft."
在二冲程循环中,只有四冲程循环的压缩和动力冲程,而没有进气和排气冲程,在活塞的一个上升冲程,一个下降冲程,同时曲轴旋转一周后完成。
In a two-stroke cycle the compression and power strokes of the four-stroke cycle are carried out without the inlet and exhaust strokes in one upstroke and one downstroke of the piston and one revolution of the crankshaft.
在二冲程循环中,只有四冲程循环的压缩和动力冲程,而没有进气和排气冲程,在活塞的一个上升冲程、一个下降冲程,同时曲轴旋转一周后完成。
"In a two-stroke cycle the compression and power strokes of the four-stroke cycle are carried out without the inlet and exhaust strokes in one upstroke and one downstroke of the piston and one revolution of the crankshaft."
在二行程发动机中,进气和压缩行以及作功和排气行分别合并在一起的,这使得二行程发动机每两个行程,即曲轴旋转一周,就完成一次工作循环。
In the two-stroke-cycle or two-cycle engine the intake and compression strokes and the power and exhaust strokes are in a sense combined.this permits the engine to produce a power stroke every two piston strokes or every crankshaft rotation.
在飞溅压力结合送油润滑系统中,油泵从油盘中把油抽上来并压入发动机机体上和曲轴上的油道
"In the combination splash and pressure feed lubricating system an oil pump takes oil from the oil pan and forces it through holes drilled in the engine block and crankshaft."
在飞溅与压力结合式送油润滑系统中,油泵从油盘中把油抽上来并压入发动机机体上和曲轴上的油道中。
In the combination splash and pressure feed lubricating system an oil pump takes oil from the oil pan and forces it through holes drilled in the engine block and crankshaft.
在曲轴密封圈的正面用3mm的钻头定点钻孔,事先在钻头上涂抹润滑脂。
Spot drill the crankshaft sealing ring on the front with a3-mm drill bit grease the drill bit beforehand.
这将防止整个进气管真空和内部曲轴箱压力影响曲轴箱强制通风,从而防止吸入发动机机油或损坏密封件。
This prevents the entire intake manifold vacuum and the internal crankcase pressure from affecting positive crankcase ventilation thereby drawing in engine oil or damaging seals.
主油泵由曲轴机械驱动。
The main oil pump is driven mechanically by the crankshaft.
组合曲轴与联轴节的大小比例,以及管子与推进轴的直径,应按照就蒸汽引擎轴系所订的规定而设计。
The proportions of built crank shafts and couplings and the diameters of tube and propeller shafts should be designed in accordance with the requirements for the shafting of steam engines.

提交更多crank的相关例句